Top-Down Bottom-Up Shades

McCordsville Top-Down Bottom-Up Shades

Light from the top, privacy from the bottom

Call (317) 999-5154Get Free Quote
Quick Answer

Read these before you choose a fabric. Material, mount and lift decisions constrain what fabrics make sense, and working in that order avoids falling for something that won't work in the room.

  • Service: Top-Down Bottom-Up Shades for McCordsville homeowners
  • Service area: McCordsville, IN and surrounding areas
    • We book measures without much delay. What you can't compress is the fabrication window, which runs two to five weeks depending on the product and the finish. Painted shutter finishes sit at the longer end.
  • Insured and bonded
  • Serving McCordsville, IN since 2008
Top-Down Bottom-Up Shades Services

Expert Top-Down Bottom-Up Shades for McCordsville Homes

Top down bottom up lift lets a shade drop from the header or rise from the sill, which matters most where houses sit close together or close to the street. The 1865 town plat is the clearest case: narrow deep lots on the original grid put houses near the sidewalk on Broadway, Main St and Center St with the long elevation to the side, and a resident who wants daylight without giving the street a view into the room needs the top open and the bottom closed. The attached product does the same job differently. The Townes at Hampton Walk runs four townhome floorplans from 1,582 to 2,157 square feet, and Gateway Crossing mixes attached and detached on the same streets.

You're buying two lift paths instead of one, and that means more hardware in the same headrail. A conventional shade has a single cord path and a single stopping mechanism. This one has a middle rail that travels, a bottom rail that travels, and separate control for each, so there are more cords and more places for the two rails to end up out of parallel with each other. The rails also stack against each other at the top, which eats more glass when the shade is fully open. Expect a higher price and a shorter interval before something needs adjusting. That's a fair trade on a narrow Broadway lot and a waste in a rear room facing open ground.

When to Call

Signs You Need Top-Down Bottom-Up Shades

If you notice any of these in your McCordsville home, it is worth booking a measure. None of it is urgent, and none of it fixes itself either.

One rail travels crooked when you push from the middle

Woven wood in the bath has swollen and sticks

The dining table sits below a window at street level

A kitchen window shows the driveway, not the yard

Existing shades force a choice between dark and exposed

The front room faces a sidewalk at eye level

Blinds stay closed all day for privacy

A dual-rail shade hangs crooked at one end

A stair window puts the top rail out of reach

A home office needs light on the ceiling, not the screen

Our Process

How McCordsville Window Treatments Handles Top-Down Bottom-Up Shades

Every job follows the same five-step process. Transparent, thorough, and done right the first time.

1

Both stacks calculated

2

Written scope and total price

3

Both rails cycled twice

4

Dust routine left with the customer

5

Rail straightening shown at handover

Real Project Photos

Top-Down Bottom-Up Shades in McCordsville

Photographs from real top-down bottom-up shades jobs completed by our crew in McCordsville and surrounding areas.

Custom shades measured and installed in McCordsvillePlantation shutters fitted to a McCordsville windowCellular shades in a McCordsville living room
Scope of Work

What Top-Down Bottom-Up Shades Includes

Every McCordsville job is documented item by item. Here is what the crew covers.

The honest hardware count stated at the measure: two rails, two lift paths and more parts than a single-lift shade

Which rail you will actually use daily talked through, since most people live in one or two positions

The sightline from the sidewalk checked with you standing in the room, because that is what sets the useful top rail height

Both stacks accounted for, the one at the head and the one that gathers under a lowered top rail

Glass left visible in the middle calculated before the order, so the open band is what you expected

Mounting depth measured for a deeper headrail, since two lift systems take more room than one

Three widths and three heights at every opening, with the diagonal read for square

Corded and cordless compared honestly, including how each one behaves when a rail drifts out of level

Cordless specified in rooms children use, since a corded dual-rail shade puts more cord in the room, not less

ANSI/WCMA A100.1-2022 cord access applied per opening rather than as one blanket line

Fabric opacity settled in writing, and the rail gap disclosed for anyone expecting blackout

Product family chosen for the room, cellular, pleated, a fabric fold or a woven natural

Weight checked against the finished size, because two rails and two lift paths add up on a wide unit

Light gap per side written on the paperwork, with the top rail position noted where it changes what you see

Rail leveling shown to you at handover so a drifted rail is a thirty second fix rather than a service call

Every opening in a room ordered together so fabric and hardware come off the same run

The contract written out in full, since IC 24-5-11 applies to residential work over $150 in this state

Both rails cycled through full travel at every window before we leave, top and bottom, twice

Pricing

What Top-Down Bottom-Up Shades Cost in McCordsville

Published national ranges put custom-fabricated shades at roughly $250 to $2,600 a window, with motorized units at roughly $300 to $1,500 per window installed. Those are national category figures rather than a quote for anything in McCordsville. A top-down bottom-up shade prices above the same shade with a single lift, and the reason is straightforward: you are buying two lift systems, a second moving rail and the hardware that carries both. Expect the upgrade to be real rather than nominal. The fabric decision then applies as usual, since a blackout cellular costs more than a light filtering pleated. Adding a motor to a dual-rail shade costs more than motorizing a single-lift one, because there are two things to move. McCordsville Window Treatments prices from measured openings across Hancock County.

By Product

How Top-Down Bottom-Up Shades Differ by Product

Every product in this trade behaves differently in a room. Here is what that means for this work.

Corded dual-rail lift: Two separate cord sets, one working the bottom rail and one working the top. It gives precise control of both rails and it puts the most cord and the most hardware into the window of any version we hang.

Cordless dual-rail lift: A spring system for the bottom rail and a second arrangement for the top, with nothing hanging beside the window. You move each rail by hand at the rail itself, which is what we specify wherever children are in the house.

Motorized dual-rail: A motor for each rail, so both positions are set from a remote or a keypad. It's the version that gets used daily on high or hard-to-reach windows, and it doubles the motor count, which shows up in both the price and the battery schedule.

Cellular top-down bottom-up: The most common build, because the cell structure stacks tightly at both ends and the fabric hides the second rail well. It's also the family with the DOE and ORNL energy testing behind the material itself.

Pleated top-down bottom-up: The lower cost version, with a single layer of pleated fabric rather than cells. It behaves the same way at both rails and gives up the trapped air pocket, which is worth saying plainly rather than leaving implied.

Fabric fold top-down bottom-up: A Roman-style shade with a movable top rail, so a formal room gets the same privacy trick without looking like a technical product. Folds stack deeper than cells, so the middle band of visible glass is narrower.

Woven natural top-down bottom-up: A bamboo or grass weave built with two rails. It looks striking and it stacks deepest of anything here, since natural material bundles rather than folds flat, so the finished size gets checked against the maker's limits first.

Room darkening fabric on a dual rail: A dense fabric on both rails, which gets a bedroom dim. The honest limit is where the two stacks meet under a lowered top rail, since that junction is hardware rather than a sealed edge and it passes a line of light.

Deeper headrail: The headrail on a dual-rail shade is larger than the one on a single-lift shade, because it houses two systems. That extra depth is the thing that most often turns a planned inside mount into an outside mount, so we measure for it early.

Outside mount with a real overlap: Mounted above and past the opening so the fabric laps the trim. On this product it does something specific: it lets the top rail drop below the head of the glass without exposing a lit gap at the sides of the opening.

Light Control

See What Each Fabric Does To The Light

Pick a fabric below and the window updates. It's a drawing rather than a photograph, so read it as a rough guide to what each family does in a McCordsville room, and to what it doesn't do.

Fabric type

Sheer, 10 percent openness

Ten percent of the weave is open, so you keep the view and most of the daylight. Glare drops a little. After dark, once your lamps are on, someone outside can read shapes through it, which is why this belongs on a view window rather than a bedroom.

Openness factor is printed on the fabric card, so you can compare one line against another before you order anything.

Keeps the viewNot private after dark

Solar, 5 percent openness

The usual pick for a west window or a covered porch. You can still read the yard through it, glare comes down noticeably, and the fabric intercepts a good share of the sun before it reaches you at four in the afternoon.

It also cuts the UV landing on floors and furniture. NFRC puts UV at roughly 40 to 60 percent of fading damage, so this slows fading rather than stopping it.

View and glare controlSlows fading

Solar, 3 percent openness

A tighter weave. The room goes dimmer and the view drops back to an outline. Choose it where the sun is the problem and the view is second, which around here usually means a west wall in July. That's a common call on this side of Indianapolis.

Openness affects how much you see out, not how private you are. A 3 percent fabric still shows silhouettes at night.

View becomes an outlineStrong glare control

Solar, 1 percent openness

Close to a solid fabric with a little view left in it. This is the strongest glare control in the solar family.

The trade is that it darkens the room on a gray January day too. Indianapolis averages a January high near 36F and the light is flat, so think about how the room reads in both seasons before you commit.

Darkest solar optionDim on gray days

Light filtering

No view through it. Daylight comes through the face diffused, so the room stays bright without a hot spot across the television or the kitchen island. This is the default for living spaces.

It isn't private in reverse at night. With the lamps on and the sun down, silhouettes still show.

No view through itBright without the glare

Room darkening

A denser fabric, usually with a liner behind it. Most of the light coming through the face is gone.

Light still arrives around the edges on an inside mount, so a room darkening shade gives you a dim room rather than a dark one. If someone in the house sleeps during the day, say so at the measure and we'll scope it differently.

Dim, not darkEdges stay bright

Blackout

The fabric itself passes essentially no light. What you'll still see is the perimeter. Lutron publishes an inside-mount light gap of about 3/4 inch per side on its Roller 20 and 64 shades, along with a standard factory deduction of 1/16 inch per side, and shades over 120 inches tall or past a 4:1 height-to-width ratio get larger gaps than that.

So if you need a genuinely dark bedroom, that gap has to be dealt with on purpose, either with side channels or by going outside mount. We tell you which one your opening can carry while we're still standing in the room.

Dark facePerimeter needs a plan

Openness factor is a measured fabric spec, so you can compare it line to line. The category names are not measured. One maker's room darkening can behave like another maker's light filtering, which is why the sample books come to the measure and get opened in the room they're going in, at the hour that room has the problem.

Common Questions

Top-Down Bottom-Up Shades FAQ

Questions we hear most often from McCordsville homeowners considering top-down bottom-up shades.

Because a normal shade raised halfway gives you the wrong half. It opens the bottom of the window, which is exactly the part your neighbor and the street can see through, and it leaves the top covered, which is where the useful daylight comes from. On a narrow lot in the old McCordsville plat, where the house next door might be twenty feet away and the sidewalk is closer than that, the top down position gives you a bright room and a private one at the same time. That's the whole argument for the product, and it's a good one.
More than a standard shade, because both rails and the folded fabric park at the header together. On a cellular fabric the stack is compact and most people never notice. On a taller shade, or one with a heavier fabric, the parked stack takes a visible band off the top of the opening. In the old village houses on Depot St and McCord St, where openings are tall and narrow and 12 to 20 of them repeat through a house, that band matters proportionally more than it does on a wide 2010s family room window. We can mount outside and above to recover it.
It can, and it's the most common service call on this product. Two independent lift paths mean two sets of cords under different tension, and uneven use over years walks the middle rail slightly out of parallel with the bottom one. It's usually a cord adjustment rather than a replacement. What makes it worse is a wide shade, because the same angular error shows as a bigger height difference across the span. On the wider openings in a Hampton Walk plan we'd sooner run two narrower shades side by side than one wide one.
Yes, and it's what we'd specify around children. The cordless version uses springs on both paths, so you push the rails where you want them by hand and they hold. The trade is that you now have two spring systems aging in one headrail instead of one, and springs weaken over years, which shows up as a rail that creeps down overnight. Products conform to ANSI/WCMA A100.1-2022, and under 16 CFR 1120.3 a non compliant inner cord counts as a substantial product hazard. That standard applies to what's manufactured, never to the company installing it.
Front facing rooms on tight lots and any room where a neighbor's second story looks down into yours, plus ground floor baths. In the subdivisions built between 2000 and 2019, which is 2,651 of the town's 4,228 units, lot spacing is generous enough that most rooms don't need it, and paying for two lift paths in a rear family room facing open ground is money spent on a feature you'll use twice. In the townhome sections and on the 1865 grid it's the opposite. Specify it where the sightline problem is real and run standard lift everywhere else.
It adds meaningfully, and the only honest numbers to quote are national. Custom fabricated window coverings run roughly $250 to $2,600 a window across the whole category, and a top down bottom up cellular shade sits above the same shade in standard lift because you're buying a second traveling rail and a second control path. Nothing installed is published for Hancock County by anyone, so treat a quoted local average as invented. Under Indiana's IC 24-5-11 you're entitled to a written contract carrying the scope, the dates and the total on any residential job above $150.
One shade, two moving rails. The bottom rail lifts the way any shade does. The top rail comes down from the head of the window, so you can drop it a foot and let daylight in over the top while the lower glass stays covered. That's the whole idea: light from above, privacy below. In a front room on a sidewalk in McCordsville, or a bath on a side elevation looking at a neighbor, it solves a problem that no single-rail shade solves.
You're buying two lift systems instead of one, plus a second rail and the hardware that carries it. That's not a small upcharge and we'd rather you hear the reason than the number alone. Nationally, custom shades run about $250 to $2,600 per window, and a dual-rail build sits meaningfully above the same shade with a single lift. Motorizing one costs more than motorizing a standard shade too, since there are two things to drive.
More hardware, more to fail. A corded version runs two separate cord paths through the shade, which means twice as many cords to fray, twice as many places to bind, and a restring job that's genuinely more involved. Cordless versions have two spring or friction systems that can wear at different rates. Neither of those is a reason to avoid the product. They're a reason to buy a good one, specify cordless where you can, and know what you're living with.
Cordless in any room children or pets use, and it isn't close. A corded dual-rail shade puts more operating cord in the room than a standard shade does, which is the opposite direction from where ANSI/WCMA A100.1-2022 points on cord access, and inner-cord non-compliance is treated as a substantial product hazard under 16 CFR 1120.3. Corded gives finer control of the top rail from across the room. In a bedroom or a nursery that isn't the trade we'd make.
Usually not to the sill, and the reason is fabric. As the top rail drops, the fabric above it has to gather somewhere, so a stack builds under the rail and grows as it comes down. On most products the top rail travels most of the drop and stops with a stack still hanging below it. On a woven natural or a fabric fold, where the material bundles deeper, it stops sooner. We show you the real travel rather than the marketing photo.
Both ends, and it's worth knowing before you order. With the shade fully raised you have the head stack. With the top rail dropped, you have that stack hanging under the rail plus the bottom stack sitting above the sill. The band of clear glass in the middle is what you're actually buying, and on a short window it can be narrower than people picture. Cellular stacks tightest. A woven natural stacks deepest. We calculate it at the measure.
It can be dim in a room darkening or blackout fabric, and it can't be sealed. There's a rail where the top section meets the fabric, and that junction is hardware, so it passes a line of light no matter what the fabric does. Add the side gaps of an inside mount, where Lutron publishes 3/4 inch per side as a real figure on their roller product, and you can see why a dark bedroom wants a different build. If a room must be dark, we layer or we mount outside with real overlap.
Usually not. On a corded shade, one side of a cord path can take up more travel than the other, and the rail ends up sitting a little low at one end. The fix is to pull the low corner down gently and let it re-seat, then run the rail full travel. We show every customer that at handover because it takes half a minute and it saves a service call. If it drifts again within a day or two, something is binding, and that we come and look at.
Rooms where you want daylight and you don't want the street. Front-facing living rooms on a sidewalk. Bathrooms on a side elevation looking straight at a neighbor. Kitchen windows over a sink where the yard is fine to see but the driveway isn't. Home offices where you want light on the ceiling and not on a screen. It's a specific answer to a specific problem, and in a back bedroom facing a wooded lot it's money you don't need to spend.
Cellular and pleated are the most common, since both stack tightly and handle a second rail cleanly. Fabric fold shades can be built this way and look lovely doing it, with a deeper stack as the tradeoff. Woven naturals can too, and they stack deepest of all. Rollers cannot, because a roller has nowhere for a second stack to go. If you've seen a roller doing something similar, it was two shades on a dual bracket, which is a different product.
More than a single-lift shade wants, yes, because the headrail houses two systems. This is the detail that most often turns a planned inside mount into an outside mount, and we measure it at the top of the opening before anything gets ordered. Where the depth isn't there, mounting outside the opening with a proper overlap is a better result than a headrail standing proud of the trim, and it usually improves privacy at the edges too.
Sometimes in the field, often at the factory, and always more involved than a single-lift shade. There are two cord paths running through the shade, so a restring means working out which path failed and threading it back through the fabric correctly. On a cordless unit, a failed lift is usually a headrail component rather than a cord, and that's typically a factory part. We'll tell you honestly which side of that line your shade falls on before you decide to repair or replace.
Yes, with two motors, one per rail, and the cost reflects that. It's the version that makes sense on tall or hard to reach windows in Hancock County, where reaching a top rail by hand means standing on something. Installed motorization sits nationally at $300 to $1,500 per window and you're driving two rails. Batteries are the recurring cost, and Hunter Douglas states PowerView battery life is about one year, which on a dual-rail shade means two battery changes rather than one.
Two to five weeks is the usual custom fabrication window and dual-rail units generally sit toward the longer end, since the second lift system gets built and tested at the factory. Motorized versions add a step. That fabrication window goes into your paperwork with the scope, the dates and the total price, which the Indiana Home Improvement Contract Act requires on residential work over $150.
Areas We Serve

Top-Down Bottom-Up Shades Across McCordsville

We measure and install in every one of these McCordsville neighborhoods. Each has its own page with the build eras, window conditions and mounting notes for that section.

Related Services

Other Window Treatment Services in McCordsville

McCordsville Window Treatments handles the full scope of window treatment work. Explore our other services below.

Faux Wood Blinds in McCordsville

Composite slats for the rooms where real wood fails

Learn more →

Wood Blinds in McCordsville

Basswood where the casing is real and the room is dry

Learn more →

Vertical Blinds in McCordsville

Door walls handled without losing half your slider

Learn more →
Free In-Home Measure

Schedule Your Free In-Home Measure in McCordsville

Contact Information

Reach Us Directly

Our team prioritizes scheduled measures and service calls, and books in-home measures during business hours.

Office
1417 Commerce Avenue, Indianapolis, IN 46201
Hours
Mon-Fri 8a-6p
Service Area
McCordsville, IN and Surrounding Areas

Ready to Book Your Measure?

Call us to set up an in-home measure, or to ask about a treatment that has stopped working. We will talk it through on the phone first.

Call (317) 999-5154
Service area

Serving McCordsville and the surrounding area

Call NowGet Quote